Hi,
is the following possible
and if so, how would these need to be configured to work so that SoftPerfect Bandwidth Manager can control the AP Clients.
Topology
Modem/Router - Assign IP via DHCP (192.168.1.1)
|
Server NIC #1 (192.168.1.100)
Win2003PC - Softperfect Bandwidth Manager
Server NIC #2 (192.168.?.?)
|
Switch
|
UniFi AP Outdoor (UAP-Outdoor)
| | |
APClient APClient APClient
Thanks
All Forums
> Bandwidth Manager
> Current topic
Network configuration with Win2003 server
Started by mongo
mongo
Network configuration with Win2003 server 17 October 2012, 22:59 |
Network Configuration 17 October 2012, 23:07 |
Admin Registered: 12 years ago Posts: 5 643 |
mongo
Network Configuration 18 October 2012, 23:09 |
Hi Andrew,
thanks for the quick response
Currently the server is running as a DNS server / Domain controller.
Would using the bandwidth manager bridging feature 'break' the functionality of the server ?
Looks like it would probably be wiser to enable DHCP on the server and use the RRAS service as you have suggested, but my router/modem has some features that I would like to keep using that I cannot replicate through the server.
I had emailed you a couple of weeks ago regards a different problem we had been having regards the following
'Unable to connect (Code: 10048, Error: Address already in use)'
But never received an email back from you.
Did you get the email (sent: 10/10/2012 16:39)
Cheers
thanks for the quick response
Currently the server is running as a DNS server / Domain controller.
Would using the bandwidth manager bridging feature 'break' the functionality of the server ?
Looks like it would probably be wiser to enable DHCP on the server and use the RRAS service as you have suggested, but my router/modem has some features that I would like to keep using that I cannot replicate through the server.
I had emailed you a couple of weeks ago regards a different problem we had been having regards the following
'Unable to connect (Code: 10048, Error: Address already in use)'
But never received an email back from you.
Did you get the email (sent: 10/10/2012 16:39)
Cheers
mongo
Network Configuration 22 October 2012, 17:21 |
Just wanted to update this thread incase someone requires a similar solution in the future
This is what is working for me
Modem/Router - Assign IP via DHCP (192.168.1.1)
|
Switch
|
DFE-580TX_LAN1
Win2003PC - Softperfect Bandwidth Manager (Tools -> Bridging)
DFE-580TX_LAN2
|
UniFi AP Outdoor (UAP-Outdoor)
| | |
APClient APClient APClient
All APClients are configured so only APClients whose MAC address is configured within the application can get a valid IP. all other MAC address are blocked.
The DHCP router is responsible for assigning all IP's.
Thanks for the assistance Andrew
This is what is working for me
Modem/Router - Assign IP via DHCP (192.168.1.1)
|
Switch
|
DFE-580TX_LAN1
Win2003PC - Softperfect Bandwidth Manager (Tools -> Bridging)
DFE-580TX_LAN2
|
UniFi AP Outdoor (UAP-Outdoor)
| | |
APClient APClient APClient
All APClients are configured so only APClients whose MAC address is configured within the application can get a valid IP. all other MAC address are blocked.
The DHCP router is responsible for assigning all IP's.
Thanks for the assistance Andrew
mongo
Network Configuration 22 October 2012, 17:24 |
Network Configuration 12 November 2012, 15:26 |
Registered: 12 years ago Posts: 172 |
The Unify system runs AirOS.
AirOS let's you set a bandwidth rate limit on each device. I already do this with some client modems with NanoStation2's.
You only need the bandwidth manager for doing quota's etc... or shaping depending on network destination.
Be careful when using bridging, if your wireless network also runs in bridge modes. Because having two many bridges and switches could cause an ARP flood (broadcast storm). If you use routed mode on your Ubiquiti gear, then this shouldn't be a problem. But if using bridged mode, make sure you understand the risks with ARP flooding.
Cheers,
Gavin.
AirOS let's you set a bandwidth rate limit on each device. I already do this with some client modems with NanoStation2's.
You only need the bandwidth manager for doing quota's etc... or shaping depending on network destination.
Be careful when using bridging, if your wireless network also runs in bridge modes. Because having two many bridges and switches could cause an ARP flood (broadcast storm). If you use routed mode on your Ubiquiti gear, then this shouldn't be a problem. But if using bridged mode, make sure you understand the risks with ARP flooding.
Cheers,
Gavin.